|
|
120mAh Single Cell. Last one in stock. No warranty no return. Discontinued by factory. SKU Number: RRC01H0120
|
|
|
|
|
120mAh Single Cell. Last one in stock. No warranty no return. Discontinued by factory. SKU Number: RRC01H0120
|
|
|
|
|
FDK (formerly Sanyo) single cell Ultra high capacity HR3U AA battery. Weight 36.9g, 1.3oz. (without tabs); Dimension: 50.4mm Long x 14.5mm Dia.; Button end cell w/Tabs; made in Japan. Unlike Sanyo's other NiMH cells, these ultra high capacity AA cells should never be fast charged EVER. We recommend 70mah (or less) wall chargers (very slow overnight charging) only. Suggested maintenance charge rate 50-70mah. Manufacturer's listed internal resistance is 25milliohm. Great for RX and TX, not a high discharge cell, not recommended for use with motors. Capacity: 2700 mAh Discharge Rate: 3 Amps Length: 1.97" / 50.4mm Diameter: 0.55" / 14.5mm Weight: 1.30 ounces / 36.9g Internal Impedence: 25 milliohm SKU Number: RRC01H2700AABET
|
|
|
|
|
FDK (formerly Sanyo). Most popular cell for S-280 and S-300 machines. Ultra long duration for GWS IPS powered ships like the Pico Stick and Tiger Moth. Perfect in 8 cell packs for Zero, Mustang and Beaver. Normally used in the 3 to 6 amp range but has applications up to 8 amps for short burst in fun-fly models. NOT for S-400, although I have used one with a lower current 7.2V S-400 setup previously. AAA size cell. Manufacturers listed internal resistance is 35m?. SKU Number: RRC01H0720
|
|
|
|
|
FDK (formerly Sanyo) AA size cell. Perfect to build your RX and TX packs. Some uses for S-400, up to 14 amp range though not common. It is the same size as any "AA" cell, but with flat ends instead of button end. We carry these for those that desire to build their own custom soldered packs. The flat ends make it much easier to solder. These may function in some digital camera and similar devices but they may not due to missing "button". Manufacturers listed internal resistance is 25m?. SKU Number: RRC01H1650FE
|
|
|
|
|
FDK (formerly Sanyo) single cell Ultra high capacity AA battery. Weight 30.3g, 1.07oz. FDK/Sanyo AA HR6 size cell. Button end cell. Unlike Sanyo's other NiMH cells, these ultra high capacity AA cells should never be fast charged EVER. We recommend 70mah (or less) wall chargers (very slow overnight charging) only. Suggested maintenance charge rate 50-70mah. Manufacturer's listed internal resistance is 25m. SKU Number: RRC01H2500AABE
|
|
|
|
|
Good cell for large applications up to 50 amps. 4/3 long "AU" size cell. Weight is 55g.
SKU Number: RRC01H4000
|
|
|
|
|
Elite SC-5000mah single cell NiMH. Dimensions: 43x23mm/1.69"x.91", Weight: 69.2g/2.4oz; Size: Sub C, May fit your screw-apart glow drivers (see notes below). Our most powerful Sub C size NiMH single cell. Special Glow Driver use notes: Some glow drivers are smaller inside than others. These cells are double shrunk, removing outer layer of clear shrink takes off about .008" making od around .901 (22.88mm). Removing the inner printed layer of shrink gets the OD down to about .895" (22.733mm). The OD of the trusty CP2400 Nicad cell is about .877" (22.276mm). Measure the ID of your glow driver before ordering to be sure it will fit. Any cell may be run without shrink in aluminum glow drivers. Note date 01/04/12. Suggested charge rate non-peak detecting 350mah or less, peak detecting .5 to 4 amps. (RX power wired packs are limited to 4 amps charge rate due to connector pins, the cell could sustain up to 10 amp peak charge rate with correct form charging, wiring and plugs. SKU Number: RRC01H5000EL
|
|
|
|
|
FDK(formerly Sanyo) single Twicell (formerly called Eneloop) NiMH AA Button End Cell. Unlike FDK(Sanyo)'s other NiMH cells, these ultra high capacity AA cells should never be fast charged EVER. We recommend 70mah (or less) wall chargers (very slow overnight charging) only. Suggested maintenance charge rate 50-70mah. Manufacturers listed internal resistance is 25m?. SKU Number: RRC01H2000TWBE
|
|
|